Mini210S
Overview
System
- CPU: 1 GHz Samsung S5PV210 with PowerVR SGX540 graphics engine (smooth 2D/3D, up to 1080p @ 30 fps decoding and encoding)
- RAM: 512 MB DDR2 RAM, 32-bit bus
- Flash: 1GB SLC NAND Flash
- EEPROM: 256 Byte (I2C)
- Ext. Memory: MicroSD card slot, Custom SDIO adapters.
- RTC: Real-Time Clock with battery
Video & Audio
- LCD Interface: 41-pin (1.0 mm) connector for FriendlyARM Displays, resistive and capacitive.
- Monitor: Mini-HDMI (type C)
- Camera: 20-pin (2.0 mm) CMOS Camera interface
- Audio Output: 3.5 mm stereo jack, connector for a speaker (Class D Amp)
- Audio Input: Condenser microphone on board
Network
- Ethernet: RJ45 10/100M (DM9000)
Other IO
- Serial Ports: 1x DB9 connector (RS232), total: 4x serial port connectors
- USB: 1x USB-A Host 2.0, 1x Mini-USB Slave/OTG 2.0
- Beeper: PWM buzzer
- User Inputs: 4x push buttons and 1x ADC pot
- User Output LEDs: 4x
- Mobile Industry Processor Interface (MIPI): 24-pin (2.0 mm) header
- SDIO Interface: 20-pin (2.0 mm) header, supports SD WiFi module, contains 1x SPI and 2x I2C
- 8×8 Keypad Interface: 20-pin (2.0 mm) header
- GPIO Interface: 10-pin (2.0 mm) header, contains ADC, I2C, I2C, SPI, PWM, IO...
- Debug: 10-pin JTAG (2.0 mm)
Mechanical
- Dimensions: 110 × 110 mm
- Temperature: 0°C to 70°C
- Power: Regulated 5V (DC-Plug)
- Weight: 98g
Hardware configuration:
- CPU processor - SOC (System On Chip)
- Samsung S5PV210, based on the ARM Cortex ™-A8, running at 1GHz
- High-performance graphics engine built-in. PowerVR SGX540
- 2D/3D graphics acceleration for supper smooth real-time graphics.
- Supports up to 1080p @ 30fps hardware decoding and smooth video playback, using MPEG4, H.263, H.264.
- Supports up to 1080p @ 30fps hardware encoding (Mpeg-2/VC1,) video input.
RAM
- Size: 512MB DDR2
- Full width 32 bit data bus, single-channel
FLASH memory
- SLC NAND Flash: 1GB (Standard)
- Supports SLC NAND Flash: 256M/512M/1GB (OEM optional)
LCD display
- LCD: 41Pin, 1.0mm pitch, same as Mini2440/Mini6410 displays.
- Touch pad support with one I2C and 3-way interrupts, 1 PWM output
- MiniHDMI HD connector (Type C)
- The LCD controller supports from 3.5 inches to 12.1 inches with screen resolution up to 1024x768.
Network (including wireless)
- 10/100M Ethernet RJ45 interface (using DM9000AEP)
Standard interface resources
- DB9 serial RS232 five lines (shares four pin TTL level serial COM 0)
- Mini USB 2.0 Slave OTG interface
- USB through the 2.0mm interface header
- 1 channel 3.5mm stereo audio output interface
- On board microphone
- External speaker interface (direct drive 8Ω 1W speaker)
- USB Host 2.0 interface
- Standard MicroSD card socket
- 5V DC voltage input
On-board resources
- I2C-EEPROM chip (256byte), mainly used to test the I2C bus
- 4 LED (green)
- 4 Push buton switches
- One Pot on ADC conversion input 0 for test.
- 1 PWM buzzer.
- On board battery backed real-time clock.
External expansion interface resources
- 4 serial connectors: TTL level, 2.0mm spacing;
- CON1, CON2 six-wire serial port - includes 5V and Gnd.
- CON3, CON4 four-wire serial port - includes 5V and Gnd
- JTAG interface: 10pin 2.0mm pitch
- LCD interface: 41pin 1.0mm pitch Chip Block
- MIPI interface: 24pin 2.0mm pitch pin header
- SDIO interface: 20pin 2.0mm pitch
- Access for SD WiFi, SDIO includes SPI and I2C interfaces
- CMOS camera interface: 20pin 2.0mm pitch.
- 8x8 matrix keyboard interface: 20pin 2.0mm pitch
- GPIO interface: 30pin, 2.0mm pitch
- Additional AD input, interrupts, I2S, I2C, SPI PWM port, digital input/output
Software Support
- Superboot
- Linux-2.6.35 + Qtopia-2.2.0/Qt-4.4.3/Qt-4.7
- Android 2.3 (Linux-2.6.35 kernel)
- Android 4.0 (Linux-3.0 kernel, only to provide the programming file)
- WindowsCE 6.0r3
Board I/O
Board connector pin outs and information for the Mini210s board, Smart and Tiny SDK board will vary.
CON1 (UART)
Linux Device: /dev/ttySAC0
WinCE 6: COM0
Notes: Is also connected to RS232 DB9 connector.
Pin | Description |
---|---|
1 | RTS |
2 | CTS |
3 | TX |
4 | RX |
5 | VDD_5V |
6 | DGND |
CON2 (UART)
Linux Device: /dev/ttySAC1
WinCE 6: COM1
Pin | Description |
---|---|
1 | RTS |
2 | CTS |
3 | TX |
4 | RX |
5 | VDD_5V |
6 | DGND |
CON3 (UART)
Linux Device: /dev/ttySAC2
WinCE 6: COM2
Pin | Description |
---|---|
1 | TX |
2 | RX |
3 | VDD_5V |
4 | DGND |
CON4 (UART)
Linux Device: /dev/ttySAC3
WinCE 6: COM3
Pin | Description |
---|---|
1 | TX |
2 | RX |
3 | VDD_5V |
4 | DGND |
CON6 (GPIO)
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | VDD_SYS_3.3V | 2 | DGND |
3 | XadcAIN1 | 4 | XEINT0 |
5 | XadcAIN2 | 6 | XEINT1 |
7 | XadcAIN6 | 8 | XEINT2 |
9 | XadcAIN7 | 10 | XEINT3 |
11 | XadcAIN8 | 12 | XEINT4 |
13 | XadcAIN9 | 14 | XEINT5 |
15 | Xi2cSDA0 | 16 | XEINT6 |
17 | Xi2cSCL0 | 18 | XEINT9 |
19 | Xi2cSDA1 | 20 | XspiCLK1 |
21 | Xi2cSCL1 | 22 | PDXspiCS1 |
23 | Xi2cSDA2 | 24 | XspiMISO1 |
25 | Xi2cSCL2 | 26 | XspiMOSI1 |
27 | XnRSTOUT | 28 | XpwmTOUT2 |
29 | XPWRRGTON | 30 | XpwmTOUT3 |
CON9 (SD WIFI)
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | VDD_SYS_3.3V | 2 | DGND |
3 | NC | 4 | NC |
5 | Xi2cSCL0 | 6 | Xi2cSDA0 |
7 | XspiMOSI0 | 8 | XspiMISO0 |
9 | XspiCLK0 | 10 | XspiCS0 |
11 | WiFi0_PD_GPIO | 12 | WiFi0_RESET_GPIO |
13 | XmmcCLK2 | 14 | XmmcCMD2 |
15 | XmmcCDn2 | 16 | WIFI1_nWP |
17 | Xmmc2DATA0 | 18 | Xmmc2DATA1 |
19 | Xmmc2DATA2 | 20 | Xmmc2DATA3 |
CON10 (Camera A)
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | Xi2cSDA0 | 2 | Xi2cSCL0 |
3 | XciFIELD/CAMERA_A_GPIO2 | 4 | CAMERA_A_RESET |
5 | XciCLKenb | 6 | XciHREF |
7 | XciVSYNC | 8 | XciPCLK |
9 | XciYDATA7 | 10 | XciYDATA6 |
11 | XciYDATA5 | 12 | XciYDATA4 |
13 | XciYDATA3 | 14 | XciYDATA2 |
15 | XciYDATA1 | 16 | XciYDATA0 |
17 | VDD_SYS_3.3V | 18 | VDD_CAMA_2.8V |
19 | VDD_CAMA_1.8V | 20 | DGND |
CON12 (Keypad 8X8 Interface)
Linux Device: /dev/buttons
WinCE 6 Driver: KEY
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | XEINT16/KP_COL0
Button K1 |
2 | XEINT24/KP_ROW0 |
3 | XEINT17/KP_COL1
Button K2 |
4 | XEINT25/KP_ROW1 |
5 | XEINT18/KP_COL2
Button K3 |
6 | XEINT26/KP_ROW2 |
7 | XEINT19/KP_COL3
Button K4 |
8 | XEINT27/KP_ROW3 |
9 | XEINT20/KP_COL4 | 10 | XEINT28/KP_ROW4 |
11 | XEINT21/KP_COL5 | 12 | XEINT29/KP_ROW5 |
13 | XEINT22/KP_COL6 | 14 | XEINT30/KP_ROW6 |
15 | XEINT23/KP_COL7 | 16 | XEINT31/KP_ROW7 |
17 | VDD_SYS_3.3V | 18 | VDD_SYS_3.3V |
19 | DGND | 20 | DGND |
CON16 (MIPI)
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | VDD_SYS_3.3V | 2 | DGND |
3 | VDD_5V | 4 | DGND |
5 | XmipiSDPCLK | 6 | XmipiMDPCLK |
7 | XmipiSDNCLK | 8 | XmipiMDNCLK |
9 | XmipiSDP0 | 10 | XmipiMDP0 |
11 | XmipiSDN0 | 12 | XmipiMDN0 |
13 | XmipiSDP1 | 14 | XmipiMDP1 |
15 | XmipiSDN1 | 16 | XmipiMDN1 |
17 | XmipiSDP2 | 18 | XmipiMDP2 |
19 | XmipiSDN2 | 20 | XmipiMDN2 |
21 | XmipiSDP3 | 22 | XmipiMDP3 |
23 | XmipiSDN3 | 24 | XmipiMDN3 |
JTAG
Row 1 Pin | Description | Row 2 Pin | Description |
---|---|---|---|
1 | VDD_SYS_3.3V | 2 | VDD_SYS_3.3V |
3 | XjTRSTn | 4 | XnRESET |
5 | XjTDI | 6 | XjTDO |
7 | XjTMS | 8 | DGND |
9 | XjTCK | 10 | DGND |
Debian on SD
Linux
Preparing an SD card to install Linux to Flash using Windows.
You will need these files from the DVD or download them here: Mini210S Linux. Superboot.bin
Install the SD-Flasher tool from the DVD or get it here. SD_Flasher Download.
Format the SD in your computer. Use FAT32 formatting.
Run-as-administrator the SD-Flasher tool and select Mini210S form the drop down menu.